Chap. 6 Troubleshooting

Parameters Table

Technical Specifications (_0 Type)
Model
Max. paper width	365mm	720mm	870mm	1100mm	1350mm
Max. cutting width	275mm	630mm	780mm	1010mm	1260mm
Cutting speed	50-800mm/s   50-800mm/s 50-800mm/s 50-800mm/s
Cutting force	50-500g   50-500g 50-500g 50-500g
Buffer capacity	1M   1M 1M 1M
LCD	Optional   Optional Optional Optional
CPU	8-bit CPU
Strip of plotter	Plastic sheet
Drive	Stepping
Min. character matrix	Approx 5 mm [0.2''] high
Blade type	Super steel [1.2mm and 2.0mm]
Film type	Self -adhesive vinyl film, fluorescent film, reflective film, paper
Display panel	8digits X 2 line LCD
Interfaces	parallel & serial
Power requirements	90-260V
Repeatability	0.0127mm
Mechanical resolution	0.0254mm/step
Commands set	DMPL / HPGL
Environmental temperature	0-35Ўж
Environmental humidity	5%-65%ЈЁwithout condensationЈ©

Technical Specifications (_1 Type)
Model
Max. paper width	365mm	720mm	870mm	1100mm	1350mm
Max. cutting width	275mm	630mm	780mm	1010mm	1260mm
Cutting speed	50-800mm/s
Cutting force	50-500g
Buffer capacity	1-4M
LCD	YES
CPU	8-bit CPU
Special setting	Dual cutter position, dual strips
Strip of plotter	Double sheet(soft sheet and plastic sheet)
Drive	Stepping
Min. character matrix	Approx. 5 mm [0.2''] high
Blade type	Super steel [1.2mm and 2.0mm]
Film type	Self -adhesive vinyl film, fluorescent film, reflective film, paper
Display panel	8digits X 2 line LCD
Interfaces	Parallel & serial, USB
Power requirements	90-260V
Repeatability	0.0127mm
Mechanical resolution	0.0254mm/step
Commands set	DMPL / HPGL
Environmental temperature	0-35Ўж
Environmental humidity	5%-65%ЈЁwithout condensationЈ©

Why is the pattern deformed or incomplete?

1. More pressure or too long blade tip or too dirty platen or too soft stickiness, all of these factors can cause more resistance to the two faces of paper and make it fall behind the roller rotating, thus result in deformed pattern.

2. The software setting isnЎЇt proper. (The tool compensation value is too big)

3. The carriage belt is too loose, or the metal roller canЎЇt exactly follow the motor running.

4. The motor doesnЎЇt run all the steps.

5. The pattern is normal but not complete, this may be resulted from too small tool compensation value.

Why does the machine plot abnormally?

1. Software setting is not matched to the machine, so you must adopt proper commands set or set proper tool compensation value.

2. The plotting software is suddenly broken up.

3. Plotting software has been damaged or there is virus in computer.

Why does the paper run deviation?

1. The stickiness isnЎЇt placed right.

2. The platen is too dirty so that the resistance from two sides canЎЇt be balanced when the paper is moving.

3. The pinch rollers have been deformed or donЎЇt match to each other.

4. The pressure of the pinch roller is a little smaller and the paper is very sensitive to the external force.

5. The balance of the stickiness weight isnЎЇt very good.

Why some parts of letters are missing?

1. The vinyl is too heavy or too tightly wrapped. Metal roller might be soiled by some foreign substance or by vinyl chips.

2. Cutting speed is too fast, cutting force is too great, or cutter tip is too long.

3. Synchromesh belt is too tight, or pinch roller is under too much pressure.

4. Metal roller is faulty. Contact local distributor for repairs and replacement.

Why different letters on the same line are cut to different depths?

1. Cutter holder is not tightly attached. It should be tightened.

2. Cutter blade is not tightly set in the holder.

Why letters appear to have ripples?

1. Cutting speed is too fast. Except for cutting large letters, speed should not exceed 480mm/s.

2. Cutting blade is of poor quality, or it has been damaged. Replace it.

3. Cutter holder is not tightly installed. Tighten screw.

Дата добавления: 2014-12-23